FHD264-S
AV and control over IP Sender with Loop output, Audio, RS232 over IP & IR
- Create a virtual video matrix with up to 64 Senders and 250 Receivers
- Works on affordable 1Gig network infrastructure
- Front panel LCD for configuration of IP parameters, and status indication
- HDMI loop output connector on FHD264-S Sender
- HDMI Audio output on each device using 3.5mm stereo connector
- PoE ready. Power supply not needed when connected to LAN with PoE
The FHD264 is a family of HDMI over LAN Senders (encoders) and receivers (decoders) utilizing advanced video encoding techniques in order to distribute up to 64 Full-HD video signals to hundreds of displays on a simple 1 Gigabit local area network(LAN). They also extend Serial RS-232 communications and IR remote signals. HDMI Audio is extracted and available on a convenient 3.5mm stereo jack on both the Sender and the Receiver. The FHD264-S Sender also provides local HDMI output.
Each device provides a two-line front panel LCD that can be used to easily configure or monitor parameters such as IP settings, multicast group selection, assignment of device names, and more. This eliminates the usual installation challenges of finding and configuring devices on the network for the first time. With the front panel LCD, users can see and assign configuration parameters with ease.
The RS-232 serial ports on each unit can be used in SoIP mode (Serial over IP). This allows 3rd party IP controllers to directly control peripheral equipment via RS-232. For example if the RS-232 of a receiver is connected to a video projector, you can turn the projector on or off via telnet commands sent to the FHD264 Receiver.
All devices support IEEE 802.3af PoE (Power over Ethernet). So when connected to a network switch with PoE, no power supply needs to be connected to the FHD264 devices. A power supply is included for customers that may not have PoE on their network.
Rack mount hardware is also available for housing up to 12 senders in 4U rack space.
NOTES:
FHD264-R Receivers also offer fail-Safe automatic video routing and redundancy. So if the receiver is not detecting any video on its currently assigned channel, it will switch to a user defined alternate channel. It can also automatically switch back to the original multicast channel if video is detected again.
FHD264 applications include digital signage, meeting rooms, classrooms, bus & metro stations, airports, home theater, and more.
The FHD264-R Receivers can decode the video from any Sender on the LAN. It is easy to switch the Receiver between Senders. This can be done in several ways:
- Using the front panel LCD and push buttons
- Using the supplied IR Remote Control
- Browsing to the WebGUI in each unit
- Telnet Commands (ideal for third-party control of switching)
- Windows PC application: DVM Manager Tool (free). Click for Instructional Video.
- CNT-IP-264 (Global Video-over-IP Controller - sold separately)
Receivers include an IR remote controller for switching among Sender channels (multicast groups). In installations such as sports bars, users can easily switch the monitor to another source using this IR remote. In addition since the FHD264 extends IR signals, users can control sources such as video players using the player's IR remote. In other words, from the Receiver location (at the TV) you use the included IR remote to switch the video to desired Sender, then you can use the IR remote of whatever is connected to the sender.
Included Accessories:
- (1) Model FHD264 (-S or -R)
- (1) 5V DC Power Supply with universal plug adapter kit and locking DC connector (Used only if no POE is available)
- (1) IR Emitter Cable (-S only)
- (1) IR Detector Cable (-R only)
- (1) IR Remote Controller (-R only)
- (1) Set of mounting bracket hardware (-S and -R)
- (1) User's Manual
- Create a virtual video matrix with up to 64 Senders and 250 Receivers
- Works on affordable 1Gig network infrastructure
- Front panel LCD for configuration of IP parameters, and status indication
- HDMI loop output connector on FHD264-S Sender
- HDMI Audio output on each device using 3.5mm stereo connector
- PoE ready. Power supply not needed when connected to LAN with PoE
- Fail-safe back up video designation to create automatic redundancy
- Serial Over IP(SoIP) to control external equipment via the Serial port
- Receivers include small IR remote controller for switching channels
- Easy to use WebGUI in each unit, accessible from any browser
- IR (infra-red) extension from Receiver to Sender
- User selectable streaming bit rate
- User-definable name for each device (e.g. Lobby Monitor, Training PC)
- Supports SD, HD and Full-HD (1080p@60 Hz) resolutions
- Free Windows PC Manager Tool software (for system-wide control)
| Input Resolution | VGA or 480p to Full HD 1080P@60 640×480@60, 800×600@60, 1024×768@60, 1280×1024@60 |
| Video Encoding | H.264 |
| Streaming Protocol | RTP/MPEG-TS/UDP |
| Casting | Unicast/Multicast |
| Control Interface | Telnet, Embedded Web Server |
| Video Latency | 250-400 mS, dependent on Bit Rate |
| Input Ports | Sender |
| Output Ports | Sender |
| Baud Rate | Bidirectional, pass thru 2400 – 115200 bps |
| Audio | HDMI Stereo 2-channel |
| IR Frequency | 38-56 KHZ pass-thru modulated 56 KHZ (IR Remote Controller) |
| Video Sources | Up to 64 |
| Video Displays | Up to 250+ |
| Recommended Network Switch/Router | Gigabit LAN |
| Operating Temp | +32 to +113F (0 to +45?) |
| Power Consumption | Max. 3 W |
| Mounting Option | Mounting Brackets (included) |
| Dimensions | 5.40(137 mm) W x 3.14(80.0 mm) D x 1.38 (35 mm) H |
| Net Weight | TX (Unit) : 0.75 lbs (0.34 KG) |
| Spec Sheets | Versions | Last Updated | |
|---|---|---|---|
|
|
FHD264-S Spec Sheet
|
2.0 | JUNE 24, 2020 |
| Manuals | Versions | Last Updated | |
|
|
FHD264 Manual
|
JUNE 24, 2020 | |
| Software | Versions | Last Updated | |
|
|
Dynamic Virtual Matrix (DVM) Manager V1.0
|
JUNE 24, 2020 | |
| Additional Downloads | Versions | Last Updated | |
|
|
FHD264 Telnet and SOIP
|
JUNE 24, 2020 | |
| Additional Downloads | Versions | Last Updated | |
|
|
Application Notes
|
JUNE 24, 2020 | |
| Additional Downloads | Versions | Last Updated | |
|
|
Video over LAN Ethernet Switch Setup
|
JUNE 24, 2020 | |
Related Products
-
HIVE Touch
Read moreHIVE Touch
The whole is greater than the sum of its parts. The Hive Touch, initially designed as a standalone and single-room AV control system, now transcends these boundaries as a synergistic solution, through Hive Node functionality and the innovative Room Combo feature. This POE-powered touch panel retains its simplicity as an intuitive user interface with a 10.1-inch multi-touch display, while expanding its capabilities to manage 2 to 100 rooms by connecting with other Hive Touches or Hive Nodes. The Hive Touch, equipped with the Hive AV App, continues to offer easy setup and command without the need for external software, embodying a blend of simplicity and expanded functionality.
-
- Complete Versa-4k and Hive Node Integration: The Hive Touch is engineered to integrate with Versa-4k systems and the Hive Node Relay, RS-232 and IR Kits, establishing a cohesive and powerful AV control network that simplifies the management of complex systems.
- Software-Free Setup: Designed with user convenience in mind, the Hive Touch eliminates the need for any additional software, allowing for all configurations and setups to be completed directly from the front panel, ensuring a user-friendly experience.
- Independent Network Operation: Emphasizing security and reliability, the Hive Touch is uniquely capable of operating on an isolated AV network, removing the dependency on internet connections or cloud services, and ensuring your AV control remains private and uninterrupted.
- Simplified Connectivity with POE: The Hive Touch is designed for ease of installation, requiring nothing more than a standard POE network switch to power up, simplifying the infrastructure needed for deployment.
-
-
Hive Node Kits
Read moreHive Node Kits
IoT controllers that offer an efficient and compact solution for controlling devices through RS-232, IR, and Relay interfaces via IP. These PoE-powered kits are designed specifically to enhance the capabilities of the Hive Touch control panel and the Hive KP8 control keypad.
- Three Kits: Hive Node Relay, Hive Node RS-232, and Hive Node IR
- Offers control over TCP/IP networks using a single Cat cable
- Equipped with IR, RS-232, and Relay accessories for diverse control
- Web interface for simple setup and POE for easy power
-
HIVE-KP8
Read more -
FHD264-R
Read moreFHD264-R
- Create a virtual video matrix with up to 64 Senders and 250 Receivers
- Works on affordable 1Gig network infrastructure
- Front panel LCD for configuration of IP parameters, and status indication
- HDMI loop output connector on FHD264-S Sender
- HDMI Audio output on each device using 3.5mm stereo connector
- PoE ready. Power supply not needed when connected to LAN with PoE
