UHBX-WP-P2

HDMI over UTP Extender with HDBaseT and PoH ( Wall Plate Sender + Receiver )

Extends HDMI or DVI video to 500 ft on just one Cat6
Supports virtually all HDMI and DVI resolutions including 4Kx2K
Only one end requires power, other side is powered via UTP
Power-over-HDBaseT meets IEEE 802.3af standard
Sturdy metal enclosures with mounting provisions
Complies fully with HDBaseT standard

Request a Quote

Description
Features
Specifications
Block Diagram
Downloads
Videos / Media

UHBX-WP-P2 is an extender kit ( combination of UHBX-S-WP + UHBX-R-PSE ) from Hall Research that utilizes HDBaseT technology. It can send HDMI and PoH (Power-over-HDBaseT) to 500 ft (150 m) on a single Cat6 cable. The extender uses only one +5v power supply, internally creates 48v PoH and complies with IEEE 802.3af handshake. The P2 extender's receiver unit provides power to the sender. In standard mode the UHBX-WP-P2 supports DVI and HDMI signals of virtually any resolution up to 4K x 2K to 330 ft (100m), and in Long Reach mode it supports resolutions to 1920x1080 to 500 ft (150 m). The devices are housed in compact and sturdy metal enclosures and have convenient mounting provisions. They are designed and manufactured in the USA.
The end identified as PSE (power sourcing equipment) injects power on to the Cat6 cable and the side identified as WP (Wall Plate) is powered through the Cat6 cable. The PSE side requires connection of an AC adapter that supplies 5v DC, while the PD side is simply powered through the RJ45 connector from the opposite side.

Two user selectable distance modes are available: Standard(default) and Long Reach. If the length of UTP cable is less than 100 meters (330 ft), then STD mode should be used. For the lengths above 330 ft Long Reach (L.R.) mode must be set. Long Reach setting can extend maximum of 1080p@60 Hz, 8-bit color (does not support deep-color or 4Kx2K) Power up to 500ft (150m).

For best results we recommend using Alliance approved cables listed at this site.

For more information about our other HDBaseT products please follow the link below to the Product Selection Chart.

Extends HDMI or DVI video to 500 ft on just one Cat6
Supports virtually all HDMI and DVI resolutions including 4Kx2K
Only one end requires power, other side is powered via UTP
Power-over-HDBaseT meets IEEE 802.3af standard
Sturdy metal enclosures with mounting provisions
Complies fully with HDBaseT standard
Runs from just one +5vDC supply
Fully isolates ground between TX and RX sides
Compact, Rugged, Reliable, and Economical
Made in USA

Max Distance	Standard Mode (STD): 330 ft (100m) Long Reach Mode (LR) : 500 ft (150m)
Video Standards	DVI (single link) and HDMI (compliant with HDMI 1.4 video specifications including 12 bit color depth, 3D video and 4K support)
Signal Type	TMDS
Connectors	Locking HDMI
Video Resolutions	DVI: VGA (640×480) to WUXGA (1920×1200) HDTV: 480i to 1080p Digital Cinema: 4K (4096×2160) Supports 4K@60 Hz (4:2:0 8 bit color) or 4K@30 Hz (4:4:4 and 8 bit color)
Audio Formats	All HDMI Embedded Audio including: LPCM 7.1CH, Dolby TrueHD and DTS-HD Master Audio (32-192kHz sample rate)
DDC	Pass-Thru DDC for reading EDID directly from remotely connected LCD and HDCP handshake
CEC	Pass-Thru DDC for Consumer Electronics Control compatible devices
PoH	Power-over-HDBaseT meets IEEE 802.3af standard. PD side identifies as Class 2 (3.846.49 watts). Actual power consumption of PD side is 5.5 watts max
Power Supply	100 VAC to 240 VAC, 50-60 Hz, external; 5 VDC, 3.2 A, regulated Actual DC current (powering both PSE and PD sides) 1.8A max
Power	Sender: 3.5 watts (12 BTU) maximum Receiver: 5.5 watts (19 BTU) maximum
Temp/humidity	Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, non-condensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, non-condensing
Cooling	Convection
Mounting	End plates have L bracket with hole for surface mounting
Enclosure	Metal (Steel ends and Aluminum extrusion)
Dimensions	1.18″ H x 4.13″ W x 4.57″ D (30mm H x 105mm W x 116mm D) Depth excludes connectors
Product weight	Sender: 9.3 oz (0.58 lb or 264 g) Receiver: 10 oz (0.63 lb or 284 g) Kit (shipping) 37 oz (2.3 lb or 1050 g) includes: sender, receiver, power supply, power cord, HDMI cable, manual, and packaging
Vibration	ISTA 1A in carton (International Safe Transit Association)
Safety	CE
EMI/EMC	CE, FCC Class A
MTBF	90,000 hours (Calculated Estimate)
Warranty	2 years parts and labor

Spec Sheets		Versions	Last Updated
	UHBX-WP-P2 Spec Sheet		JUNE 24, 2020
Manuals		Versions	Last Updated
	UHBX-WP-P2 Manual		JUNE 24, 2020

UHBX-WP-P2

HDMI over UTP Extender with HDBaseT and PoH ( Wall Plate Sender + Receiver )

Email Sign Up

Products

Navigation

Solutions

UHBX-WP-P2

HDMI over UTP Extender with HDBaseT and PoH ( Wall Plate Sender + Receiver )

Related Products

UH18-S

UH18-S

EX-LYNX-WP-TX

EX-LYNX-WP-TX

EX-LYNX-WPE-TX

EX-LYNX-WPE-TX

UH18 (Kit)

UH18 (Kit)

HDMI over UTP Extender with HDBaseT and PoH ( Wall Plate Sender + Receiver )