discontinued

UHBX-S-PD

HDMI+RS232+IR+PoH UTP (Sender)

  • Extends HDMI or DVI video to 500 ft on just one Cat6
  • Includes RS232 and IR extension in both directions
  • Supports virtually all HDMI and DVI resolutions including 4Kx2K
  • Only one end requires power, other side is powered via UTP
  • Power-over-HDBaseT™ meets IEEE 802.3af standard
  • Sturdy metal enclosures with mounting provisions
    Request a Quote

    Accessories

    CIR-EMT

    IR Emitter Cable

    Read More

    CIR-DET-P2

    IR Receiver Cable with carrier pass through (Type 2)

    Read More

    UHBX-S-PD sender module when paired with compatible receiver ( Hall Research model UHBX-R-PSE ), can extend HDMI, bi-directional IR, full-duplex RS232, and PoH (power over HDBaseT™) over distances of up to 150 meters (500 feet) using a single Cat6 cable. The pair can extend HDMI or single-link DVI video of virtually any resolution, to a maximum distance of 500 ft (150 m). Moreover, these extenders complies with Power-over-HDBaseT™ or PoH, hence only one end requires a power supply . The end identified as PSE (power sourcing equipment) injects power on to the Cat6 cable and the side identified as PD (powered device) is powered through the Cat6 cable. The PSE side requires connection of an AC adapter that supplies 5v DC, while the PD or WP(wall plate) side is simply powered through the RJ45 connector from the opposite side.

    Full-duplex RS232 Serial Port extension is provided that can operate at any baud rate to 115,200 (independent of video activity). The extender can also extend IR from one end to the other. IR Detector and IR Emitter cables are sold separately. The IR extension preserves the modulation(carrier) frequency and provides compatibility to virtually any standard. It supports modulation range from 30 KHz to 60 KHz.

    UHBX-S-PD is fully compatible with the following HDBaseT™ receiver from Hall Research:

    For best results we recommend using Alliance approved cables listed at this site.

    UHBX-S-PD is also partially compatible with other HDBaseT™ receivers from Hall Technologies.

    For more information about product compatibility, please follow the link below to the Product Selection Chart.

    HDBaseT Compatibility Chart

    • Extends HDMI or DVI video to 500 ft on just one Cat6
    • Includes RS232 and IR extension in both directions
    • Supports virtually all HDMI and DVI resolutions including 4Kx2K
    • Only one end requires power, other side is powered via UTP
    • Power-over-HDBaseT™ meets IEEE 802.3af standard
    • Sturdy metal enclosures with mounting provisions
    • Complies fully with HDBaseT™ standard
    • Runs from just one +5vDC supply
    • RS232 Supports all baud rates regardless of presence of video
    • IR extension is carrier frequency agnostic and supports 30 KHz to 60 KHz modulation to provide compatibility across all IR standards
    • Fully isolates ground between TX and RX sides
    • Compact, Rugged, Reliable, and Economical
    • Made in USA
    Max Distance

    Standard Mode (STD): 330 ft (100m)
    Long Reach Mode (LR) : 500 ft (150m)
    Video Standards

    DVI (single link) and HDMI (compliant with HDMI 1.4 video specifications including 12 bit color depth, 3D video and 4K support)
    Signal Type

    TMDS
    Connectors

    Locking HDMI
    Video Resolutions

    DVI: VGA (640×480) to WUXGA (1920×1200)
    HDTV: 480i to 1080p
    Digital Cinema: 4K (4096×2160)
    Supports 4K@60 Hz (4:2:0 8 bit color) or 4K@30 Hz (4:4:4 and 8 bit color)
    Audio Formats

    All HDMI Embedded Audio including: LPCM 7.1CH, Dolby TrueHD and DTS-HD Master Audio (32-192kHz sample rate)
    DDC

    Pass-Thru DDC for reading EDID directly from remotely connected LCD and HDCP handshake
    CEC

    Pass-Thru DDC for Consumer Electronics Control compatible devices
    RS232

    Bi-directional (full-duplex) any baud rate upto 115,200
    IR

    Extended in both directions. Carrier modulation range from 30 KHz to 60
    KHz
    PoH

    Power-over-HDBaseT™ meets IEEE 802.3af standard. PD side identifies as
    Class 2 (3.84–6.49 watts). Actual power consumption of PD side is 5.5 watts
    max
    Power Supply

    100 VAC to 240 VAC, 50-60 Hz, external; 5 VDC, 3.2 A, regulated
    Actual DC current (powering both –PSE and –PD sides) 1.8A max
    Power

    Sender: 3.5 watts (12 BTU) maximum
    Receiver: 5.5 watts (19 BTU) maximum
    Temp/humidity

    Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, non-condensing
    Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, non-condensing
    Cooling

    Convection
    Mounting

    End plates have L bracket with hole for surface mounting
    Enclosure

    Metal (Steel ends and Aluminum extrusion)
    Dimensions

    1.18″ H x 4.13″ W x 4.57″ D (30mm H x 105mm W x 116mm D) Depth excludes connectors
    Product weight

    Sender: 9.3 oz (0.58 lb or 264 g)
    Receiver: 10 oz (0.63 lb or 284 g)
    Kit (shipping) 37 oz (2.3 lb or 1050 g) includes: sender, receiver, power supply, power cord, HDMI cable, manual, and packaging
    Vibration

    ISTA 1A in carton (International Safe Transit Association)
    Safety

    CE
    EMI/EMC

    CE, FCC Class A
    MTBF

    90,000 hours (Calculated Estimate)
    Warranty

    2 years parts and labor

    Manuals Versions Last Updated
    		UHBX-S-PD Manual

    		JUNE 24, 2020
    Additional Downloads Versions Last Updated
    		App Note - IR Cables for the UHBX Series

    		JUNE 24, 2020
    Additional Downloads Versions Last Updated
    		UHBX-S-PD Dimensional DXF

    		JUNE 24, 2020
    Additional Downloads Versions Last Updated
    		UHBX-S-PD Dimensional PDF

    		JUNE 24, 2020

    Related Products