UHBX-R-PD

HDBaseT Receiver with HDMI output, Bidirectional IR, RS232, and PoH Sink (Power over HDBaseT)

  • Extends HDMI or DVI video to 500 ft on just one Cat6
  • Includes RS232 and IR extension in both directions
  • Supports virtually all HDMI and DVI resolutions including 4Kx2K
  • Only one end requires power, other side is powered via UTP
  • Power-over-HDBaseT™ meets IEEE 802.3af standard
  • Sturdy metal enclosures with mounting provisions

Accessories

CIR-EMT

IR Emitter Cable

Read More

CIR-DET-P2

IR Receiver Cable with carrier pass through (Type 2)

Read More

UHBX-R-PD receiver module when paired with compatible sender ( Hall Research model UHBX-S-PSE ), can extend HDMI, bi-directional IR, full-duplex RS232, and PoH (power over HDBaseT™) over distances of up to 150 meters (500 feet) using a single Cat6 cable. The pair can extend HDMI or single-link DVI video of virtually any resolution, to a maximum distance of 500 ft (150 m). Moreover, these extenders complies with Power-over-HDBaseT™ or PoH, hence only one end requires a power supply . The end identified as PSE (power sourcing equipment) injects power on to the Cat6 cable and the side identified as PD (powered device) is powered through the Cat6 cable. The PSE side requires connection of an AC adapter that supplies 5v DC, while the PD or WP(wall plate) side is simply powered through the RJ45 connector from the opposite side.

Full-duplex RS232 Serial Port extension is provided that can operate at any baud rate to 115,200 (independent of video activity). The extender can also extend IR from one end to the other. IR Detector and IR Emitter cables are sold separately. The IR extension preserves the modulation(carrier) frequency and provides compatibility to virtually any standard. It supports modulation range from 30 KHz to 60 KHz.

Two user selectable distance modes are available: Standard(default) and Long Reach. If the length of UTP cable is less than 100 meters (330 ft), then STD mode should be used. For the lengths above 330 ft Long Reach (L.R.) mode must be set. Long Reach setting can extend maximum of 1080p@60 Hz, 8-bit color (does not support deep-color or 4Kx2K) , RS232, IR and Power up to 500ft (150m)

UHBX-R-PD is fully compatible with the following HDBaseT™ senders from Hall Technologies:

For best results we recommend using Alliance approved cables listed at this site.

UHBX-R-PD is also partially compatible with other HDBaseT™ senders from Hall Technologies.

For more information about product compatibility, please follow the link below to the Product Selection Chart.

HDBaseT Compatibility Chart

  • Extends HDMI or DVI video to 500 ft on just one Cat6
  • Includes RS232 and IR extension in both directions
  • Supports virtually all HDMI and DVI resolutions including 4Kx2K
  • Only one end requires power, other side is powered via UTP
  • Power-over-HDBaseT™ meets IEEE 802.3af standard
  • Sturdy metal enclosures with mounting provisions
  • Complies fully with HDBaseT™ standard
  • Runs from just one +5vDC supply
  • RS232 Supports all baud rates regardless of presence of video
  • IR extension is carrier frequency agnostic and supports 30 KHz to 60 KHz modulation to provide compatibility across all IR standards
  • Fully isolates ground between TX and RX sides
  • Compact, Rugged, Reliable, and Economical
  • Made in USA
Max Distance

Standard Mode (STD): 330 ft (100m)
Long Reach Mode (LR) : 500 ft (150m)

Video Standards

DVI (single link) and HDMI (compliant with HDMI 1.4 video specifications including 12 bit color depth, 3D video and 4K support)

Signal Type

TMDS

Connectors

Locking HDMI

Video Resolutions

DVI: VGA (640×480) to WUXGA (1920×1200)
HDTV: 480i to 1080p
Digital Cinema: 4K (4096×2160)
Supports 4K@60 Hz (4:2:0 8 bit color) or 4K@30 Hz (4:4:4 and 8 bit color)

Audio Formats

All HDMI Embedded Audio including: LPCM 7.1CH, Dolby TrueHD and DTS-HD Master Audio (32-192kHz sample rate)

DDC

Pass-Thru DDC for reading EDID directly from remotely connected LCD and HDCP handshake

CEC

Pass-Thru DDC for Consumer Electronics Control compatible devices

RS232

Bi-directional (full-duplex) any baud rate upto 115,200

IR

Extended in both directions. Carrier modulation range from 30 KHz to 60
KHz

PoH

Power-over-HDBaseT™ meets IEEE 802.3af standard. PD side identifies as
Class 2 (3.84–6.49 watts). Actual power consumption of PD side is 5.5 watts
max

Power Supply

100 VAC to 240 VAC, 50-60 Hz, external; 5 VDC, 3.2 A, regulated
Actual DC current (powering both –PSE and –PD sides) 1.8A max

Power

Sender: 3.5 watts (12 BTU) maximum
Receiver: 5.5 watts (19 BTU) maximum

Temp/humidity

Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, non-condensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, non-condensing

Cooling

Convection

Mounting

End plates have L bracket with hole for surface mounting

Enclosure

Metal (Steel ends and Aluminum extrusion)

Dimensions

1.18″ H x 4.13″ W x 4.57″ D (30mm H x 105mm W x 116mm D) Depth excludes connectors

Product weight

Sender: 9.3 oz (0.58 lb or 264 g)
Receiver: 10 oz (0.63 lb or 284 g)
Kit (shipping) 37 oz (2.3 lb or 1050 g) includes: sender, receiver, power supply, power cord, HDMI cable, manual, and packaging

Vibration

ISTA 1A in carton (International Safe Transit Association)

Safety

CE

EMI/EMC

CE, FCC Class A

MTBF

90,000 hours (Calculated Estimate)

Manuals Versions Last Updated
UHBX-R-PD Manual

JUNE 24, 2020
Additional Downloads Versions Last Updated
App Note - IR Cables for the UHBX Series

JUNE 24, 2020
Additional Downloads Versions Last Updated
UHBX-R-PD Dimensional DXF

JUNE 24, 2020
Additional Downloads Versions Last Updated
UHBX-R-PD Dimensional PDF

JUNE 24, 2020